![Osciloscopio tektronix multisim 12](https://knopkazmeya.com/5.png)
- #OSCILOSCOPIO TEKTRONIX MULTISIM 12 GENERATOR#
- #OSCILOSCOPIO TEKTRONIX MULTISIM 12 FULL#
- #OSCILOSCOPIO TEKTRONIX MULTISIM 12 SOFTWARE#
- #OSCILOSCOPIO TEKTRONIX MULTISIM 12 SERIES#
After that happens once, all read or write functions also produce this same error for a while. However, I noticed that after a few hours, there are apparently random of chances that a VISA to read or write the block function will produce the error - 1073807339. My program is intended to be run for hours at a time, and it works perfectly as expected for the first few hours. I am trying to make measurements of waveform of an oscilloscope Tektronix 1052 B using LabVIEW.
#OSCILOSCOPIO TEKTRONIX MULTISIM 12 SERIES#
The measured values and the calculated values were very close to each other and thus the lab exercise was a success.Error time-out random - 1073807339 using pilots of series Oscilloscope Tektronix TDS 200 1000 2000
#OSCILOSCOPIO TEKTRONIX MULTISIM 12 FULL#
This lab exercise was a good insight in the study and design of a half wave rectifier and a full wave rectifier. The output voltage of a full wave rectifier is more linear than the output voltage of a half wave rectifier. How is the output of the full-wave rectifier different from half-wave rectifier? It conducts for both the positive going cycle and the negative going cycle.ġ.
![osciloscopio tektronix multisim 12 osciloscopio tektronix multisim 12](https://i.ytimg.com/vi/ubvyEaLYYA0/maxresdefault.jpg)
What is the purpose of having a full-wave rectifier in the circuit?Ī full-wave rectifier converts the alternating AC voltage into a pulsating DC voltage. The function of the capacitor is to reduce the ripples in the output voltage and make it more like a DC voltage.ġ. Discuss the impact of having the capacitor on the output voltage and the effect of additional load on the ripple voltage.
![osciloscopio tektronix multisim 12 osciloscopio tektronix multisim 12](http://de.owontech.com/uploads/202012477/small/4-ch-tablet-digital-oscilloscope39554743586.jpg)
#OSCILOSCOPIO TEKTRONIX MULTISIM 12 SOFTWARE#
The connections on the breadboard and in the MULTISIM software were done as per the connection diagram.ġ. Describe the procedure in this lab to arrive at the final design of both the hardware portion and the software portion to achieve the design objectives? It converts the positive going cycles of an alternating AC voltage into a pulsating DC voltage.ġ. What is the purpose of having a half-wave rectifier in the circuit? The measured and the calculated values were summarized in the tables below:ġ. Load voltage without the filter capacitorġ. Peak to peak voltage with filter capacitorġ. Load voltage measurement with the filter capacitorįull wave rectifier MULTISIM measurementsġ. Peak to peak ripple voltage with the filter capacitorġ. Half wave rectifier MULTISIM measurementsġ. The full-wave rectifier circuit is constructed as shown below: The half wave rectifier is constructed as shown in the figure below: The peak to peak ripple voltage is equal to The ripple frequency is equal to 2*F=1*60Hz=120Hz The peak to peak ripple voltage is equal to 1.4213V-0V=1.4213V The RMS load voltage is equal to 1.4213/sqrt(2)=1.005V The peak secondary voltage is equal to 1.5*sqrt(2)= 2.1213V The secondary voltage is equal to 30V/(10*2)=1.5V The turns-ratio of the transformer is 10:1 Half wave rectifier with the filter capacitor: The ripple frequency is equal to the source frequency=60Hz The peak to peak ripple voltage is equal to: 3.5426-0=3.5426V The peak secondary voltage is equal to 3*sqrt(2)= 4.2426V The secondary RMS voltage is: 30V/10=3VRMS The circuits shown in the figure below both for the half-wave rectifier and a full wave rectifier are to be constructed in MULTISIM and on a breadboard.įor the half wave rectifier the calculations are done as follows: Oscilloscope (NI Elvismx Instrument Launcher)
#OSCILOSCOPIO TEKTRONIX MULTISIM 12 GENERATOR#
Arbitrary Waveform Generator (NI Elvismx Instrument Launcher)ġ. Function Generator (NI Elvisms Instrument Launcher)ġ.
![osciloscopio tektronix multisim 12 osciloscopio tektronix multisim 12](https://mirror2.mixtronica.com/46559-superlarge_default/tbs1102b-osciloscopio-tektronix-2-canais-100mhz.jpg)
One fuse (any rating is fine since it is for simulation only)ġ. One 100 μF, 50 V electrolytic capacitorġ.
![osciloscopio tektronix multisim 12 osciloscopio tektronix multisim 12](https://cdn.wallapop.com/images/10420/3j/bh/__/c10420p213846791/i482019209.jpg)
The calculate values are to be compared with the measured values to check for consistency.ġ. The myDAQ is to be used for data acquisition from the breadboard to the MULTISIM software. The various output voltage are to be measured. The purpose of this lab exercise is to build a half wave rectifier and a full wave rectifier in MULTISIM and on a breadboard.
![Osciloscopio tektronix multisim 12](https://knopkazmeya.com/5.png)